MSDS Certificated Lithium Polymer Batteries
3.7V Rechargeable LiPo Batteries Manufacturer Supplier, MSDS certificated lithium polymer batteries for your new device
What is the MSDS?
MSDS is Material Safety Data Sheet (MSDS), A Material Safety Data Sheet (MSDS) is a document that contains information on the potential hazards (health, fire, reactivity, and environmental) and how to work safely with the chemical product. It is an essential starting point for the development of a complete health and safety program. It also contains information on the use, storage, handling, and emergency procedures all related to the hazards of the material. The MSDS contains much more information about the material than the label. MSDSs are prepared by the supplier or manufacturer of the material. It is intended to tell what the hazards of the product are, how to use the product safely, what to expect if the recommendations are not followed, what to do if accidents occur, how to recognize symptoms of overexposure, and what to do if such incidents occur.
IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND OF THE COMPANY/UNDERTAKING
Recommended use of the chemical and restrictions on use
Recommended Use: Used in portable electronic equipment;
Uses advised against:
a)Do not dismantle, open or shred secondary cells or batteries.
b)Do not expose cells or batteries to heat or fire. Avoid storage in direct sunlight.
c)Do not short-circuit a cell or a Lithium Polymer battery. Do not store cells or batteries haphazardly in a box or drawer where they may short-circuit each other or be shore-circuited by other metal objects.
d)Do not remove a cell or Lithium Polymer battery from its original packaging until required for use.
e)Do not subject cells or batteries to mechanical shock.
f)In the event of a cell leaking, do not allow the liquid to come in contact with the skin or eyes. If contact has been made, wash the affected area with copious amounts of water and seek medical advice.
g)Do not use any charge other than that specifically provided for use with the equipment.
h)Observe the plus(+) and minus(-)marks on the cell, Lithium Polymer battery, and equipment and ensure correct use.
i)Do not use any cell or Lithium Polymer battery that is not designed for use with equipment.
j)Do not mix cells of different manufacture, capacity, size, or type within a device.
k)Lithium Polymer Batteries usage by children should be supervised.
I)Seek medical advice immediately if a cell or Lithium Polymer Batteries has been swallowed.
m)Always purchase Lithium Polymer Batteries recommended by the device manufacturer for the equipment.
n)Keep cells and batteries clean and dry.
o)Wipe the cell or Lithium Polymer Batteries terminals with a clean dry cloth if they become dirty.
p)Secondary cells and batteries need to be charged before use. Always use the correct charger and refer to the manufacturer’s instructions or equipment manual for proper charging instructions.
q)Do not leave Lithium Polymer Batteries on prolonged charge when not in use.
r)After extended periods of storage, it may be necessary to charge the discharge of the cells or Lithium Polymer Batteries several times to obtain maximum performance.
s)Retain the original product literature for future reference.
t)Use only the cell or Lithium Polymer Batteries in the application for which it was intended.
u)When possible, remove Lithium Polymer Batteries from the equipment when not in use.
v)Dispose of properly.
2. HAZARDS IDENTIFICATION
No harm at the normal use. If contact the Electrolyte liquid in the Li-ion Battery, reference as follows:
Classification of the substance or mixture
Classification according to GHS
Acute Toxicity, Oral(Hazard category 4)
Acute Toxicity, Dermal(Hazard category 3)
Skin, irritate(Cagegory 1B)
Eye Irrtate(Hazard category 1)
3. COMPOSITION/INFORMATION ON INGREDIENTS
Chemical characterization: Mixtures
Product: Consisting of the following components.
Note: CAS number is Chemical Abstract Service Registry Number.
4. FIRE-FIGHTING MEASURES
Suitable Extinguishing Media
CO2, dry chemical powder, water spray.
Specific Hazards Arising from the Chemical
The formation of toxic gases is possible during heating or in the case of fire.
In case of fire, the following can be released:
Other irritating and toxic gases.
Hazardous Combustion Products
Sensitivity to Mechanical Impact No
Sensitivity to Static Discharge No
Protective Equipment and Precautions for Firefighters
As in any fire, wear self-contained breathing apparatus pressure-demand, MSHA/NIOSH(approved or equivalent), and full protective gear. For example: Wear a self-contained respiratory protective device.
Wear suitable protective clothing and eye/face protection.
Special hazards arising from the substance or mixture:
Lithium Polymer Batteries may burst and release hazardous decomposition products when exposed to a fire situation.
Lithium-ion batteries contain flammable electrolytes that may vent, ignite and produce sparks when subjected to high temperature(>150°C), When damaged or abused(e.g. mechanical damage or electrical overcharging); may burn rapidly with flare-burning effect; may ignite other batteries in clothes proximity.
5. ACCIDENTAL RELEASE MEASURES
Personal precautions, protective equipment, and emergency procedures
Personal Precautions Avoid contact with eyes.
Refer to section 8 for personal protective equipment. Ensure adequate ventilation. Remove all sources of ignition.
Evacuate personnel to safe areas.
Absorb with liquid-binding material(sand, diatomite, acid binders, universal binders, sawdust).
Methods and material for containment and cleaning up
Methods for containment Prevent further leakage or spillage if safe to do so.
Methods for cleaning up Use personal protective equipment. Dam up. Cover liquid spill with sand, earth, or other Non-combustible absorbent material. Pick up and transfer to properly labeled containers. Clean contaminated surfaces thoroughly.
6. FIRST-AID MEASURES
Eye Contact Rinse thoroughly with plenty of water, also under the eyelids. If symptoms persist, call a physician.
Skin Contact Remove contaminated clothing and shoes. Wash skin with soap and water. In the case of skin irritation or allergic reactions see a physician.
Inhalation Move to fresh air. If symptoms persist, call a physician.
Ingestion Do NOT induce vomiting. Drink plenty of water. If symptoms persist, call a physician.
Most important symptoms and effects, both acute and delayed
Swallowing Do not induce vomiting. Get medical attention.
7. HANDLING AND STORAGE
Precautions for safe handling
Handle in accordance with good industrial hygiene and safety practices. Avoid contact with skin, eyes, and clothing. Wear personal protective equipment.
Wash thoroughly after handling. Use this material with adequate ventilation.
The product is not explosive.
Conditions for safe storage, including andy incompatibilities.
If the Lithium-ion Battery is subject to storage for such a long term as more than 3 months, it is recommended to recharge the Lithium Polymer Batteries periodically.
3 months: -10°C~+40°C, 45 to 85%RH.
And recommended at 0°C~+35°C for long period storage.
The capacity recovery rate in the delivery state(50% capacity of fully charged)after the storage is assumed to be 80% or more.
The voltage for long time storage shall be 3.8V~4.8V range.
Do not store Lithium Polymer Batteries haphazardly in a box or drawer where they may short-circuit each other or be short-circuited by other metal objects.
Keep out of reach of children.
Do not expose Lithium Polymer Batteries to heat or fire. Avoid storage in direct sunlight.
Do not store together with oxidizing and acidic materials.
Keep ignition sources away—Do not smoke.
Store in a cool, dry, and well-ventilated place.
8. EXPOSURE CONTROLS AND PERSONAL PROTECTION
Individual protection measures, such as personal protective equipment
9. STABILITY AND REACTIVITY
Reactivity: Stable under recommended storage and handling conditions.
Chemical stability: Stable under normal conditions of use, storage, and transport.
Thermal decomposition/conditions to be avoided: No decomposition if used according to specifications.
Possibility of Hazardous Reactions: None under normal processing.
Hazardous Polymerization: Hazardous polymerization does not occur.
Conditions to avoid: Strong heating, fire, Incompatible materials.
Incompatible materials: Strong oxidizing agents. Strong acids. Base metals.
Hazardous Decomposition Products: Carbon oxides, other irritating and toxic gases.
10. DISPOSAL CONSIDERATIONS
Waste treatment methods
Recommendation: Must not be disposed of together with household garbage.
Do not allow product to reach sewage system
Recommendation: Disposal must be made according to official regulations.
11. TRANSPORT INFORMATION
Lithium Polymer Batteries had been tested according to the requirements of the UN Manual of Tests and Criteria.
Lithium Polymer Batteries with a Watt-hour rating not exceeding 100Wh or the cell with a Watt-hour rating not exceeding of 20Wh.
The packaging shall be adequate to avoid mechanical damage during transport, handling, and stacking. The materials and pack design shall be chosen so as to prevent the development of unintentional electrical conduction, corrosion of the terminals, and ingress of moisture.
Meets requirements of International Maritime Dangerous Goods(IMDG)-2014 Special Provision 188 to be transported as non-dangerous goods;
Meets the requirements of 49CFR173.185 to be transported as non-dangerous goods for road, rail, air, and vessel.
Meets the requirements of TDG special provision 34 to be transported as non-dangerous goods.
The package must be handled with care and that a flammability hazard exists if the package is damaged;
Caution! – Lithium Polymer Batteries
In order to prevent the Lithium Polymer Battery possibly occurs leaks, overheat, swollen, please note the preventive measure.
Handling Precautions and Guideline:
When charge please select the lithium-polymer battery special battery charger.
Strictly prohibits inverting the cathode use Lithium Polymer Battery.
Strictly prohibits directly connect Lithium Polymer Battery to power source plug
Please do not throw the Lithium Polymer Battery to water or put into heater
Strictly prohibits plunging the Lithium Polymer Battery in sea water or water, when Lithium Polymer Battery do not use, please store Lithium Polymer Battery in the cool-dry environment.
The prohibition in strong static electricity and strong magnetic field place use, otherwise is easy to destroy the Lithium Polymer Battery PCBA
The prohibition puts the Lithium Polymer Battery nearby the hot high temperature source, like the fire, the heater and so on use and leaves alone
The prohibition directly connects the Lithium Polymer Battery cathode with the metal to short-circuit.
The prohibition rap or throws, steps on the Lithium Polymer Battery and soon
Forbids directly to weld the Lithium Polymer Battery and pierces the Lithium Polymer Battery with the nail or other sharp weapons
If the Lithium Polymer Battery sends out the unusual smell, gives off heat, the distortion or appears any exceptionally, immediately moves the Lithium Polymer Battery from the installment or the battery charger to and stops using
If the Lithium Polymer Battery occurs leaks, the electrolyte enters eye, please do not have to rub scratches, the application clear water flushing eye, and delivers the medical treatment otherwise to be able immediately to injure the eye
When Lithium Polymer Battery long-term storage, or assembly in the host, suggest customer should take every 6months carry on one time charge and discharge and recharge it to half charge state (3.7-3.9V)(the method: 0.2CmA charge and discharge)
Abandon the battery to wrap up the electrode using the insulating paper, prevented the Lithium Polymer Battery short-circuits
Do not decompose the Lithium Polymer Battery
Keep small LiPo cells and Lithium Polymer Batteries which are considered swallowable out of the reach of children
Swallowing may lead to burns, perforation of soft tissue, and death. Severe burns can occur within 2 h of ingestion
In case of ingestion of a LiPo cell or Lithium Polymer Battery, seek medical assistance promptly.
3.7V 18650 Li-ion Battery 18650D 2200mAh 8.14Wh
3.7V 18650 Li-ion Battery 18650D 2200mAh 8.14Wh With PCM & wires 50mm Model 3.7V 18650 Li-ion Battery 18650D 2200mAh 8.14Wh Type Rechargeable Li-ion battery Capacity 2200mAh Voltage 3.7V Energy 8.14Wh Net Weight 65 g Detail Protection circuit&50mm wires...
LP502025 180mAh 3.7V Rechargeable Lithium Polymer Battery with connector JST SHR-02V-S-B A
LP502025 180mAh 3.7V Rechargeable Lithium Polymer Battery with connector JST SHR-02V-S-B A With PCM & wires 50mm LiPo battery Type LP502025 180mAh 3.7V Rechargeable Lithium Polymer Battery with connector JST SHR-02V-S-B A Voltage 3.7V Lithium Polymer Battery...
3.7V Rechargeable Hot Selling Lithium Polymer Batteries LP603064 2400mAh
3.7V Rechargeable Hot Selling Lithium Polymer Batteries LP603064 2400mAh With PCM & wires 50mm & connector Molex LiPo battery Type 3.7V Rechargeable Hot Selling Lithium Polymer Batteries LP603064 2400mAh Voltage 3.7V Energy 8.88Wh Net Weight 60g Detail...
Certificated 3.7V Rechargeable Lithium Polymer Batteries LP903450 1500mAh
Certificated 3.7V Rechargeable Lithium Polymer Batteries LP903450 1500mAh With PCM & wires 50mm & JST connector LiPo battery Type Certificated 3.7V Rechargeable Lithium Polymer Batteries LP903450 1500mAh Voltage 3.7V Energy 5.55Wh Net Weight 30g Detail...
Certificated 3.7V Rechargeable Lithium Polymer Batteries LP103740 1580mAh
Certificated 3.7V Rechargeable Lithium Polymer Batteries LP103740 1580mAh With PCM & wires 50mm LiPo battery Type Certificated 3.7V Rechargeable Lithium Polymer Batteries LP103740 1580mAh Voltage 3.7V Energy 5.85Wh Net Weight 30g Detail Protection circuit&50mm...
Rechargeable 3.7V Lithium Polymer Battery LP401030 90mAh
Rechargeable 3.7V Lithium Polymer Battery LP401030 90mAh With PCM and wires 50mm LiPo battery Type Rechargeable 3.7V Lithium Polymer Battery LP401030 90mAh Voltage 3.7V Energy 0.333Wh Net Weight 1 g Detail Protection circuit&50mm wires LiPo Battery Size 4.0mm*...
3.7V Standard Rechargeable Lithium Polymer Batteries With JST SHR-03V-S-B LP102731 850mAh 0.3145Wh
3.7V Standard Rechargeable Lithium Polymer Batteries With JST SHR-03V-S-B LP102731 850mAh 0.3145Wh With PCM & wires 50mm & JST connector LiPo battery Type 3.7V Standard Rechargeable Lithium Polymer Batteries With JST SHR-03V-S-B LP102731 850mAh 0.3145Wh...
Hot Selling Lithium Polymer Batteries LP503759 1200mAh 4.44Wh
Hot Selling Lithium Polymer Batteries LP503759 1200mAh 4.44Wh With PCM & 10k NTC & wires 50mm & connector LiPo battery Type Hot Selling Lithium Polymer Batteries LP503759 1200mAh 4.44Wh Voltage 3.7V Energy 4.44Wh Net Weight 30g Detail Protection...
Standard lithium polymer batteries LP286380 2000mAh with 7.4Wh
Standard lithium polymer batteries LP286380 2000mAh with 7.4Wh With PCM & 10K NTC & wires 50mm & connector LiPo battery Type Standard lithium polymer batteries LP286380 2000mAh with 7.4Wh Voltage 3.7V Energy 7.4Wh Net Weight 50g Detail Protection...
3.7V Rechargeable Hot Selling Lithium Polymer Batteries LP652526 350mAh with 1.295Wh
3.7V Rechargeable Hot Selling Lithium Polymer Batteries LP652526 350mAh with 1.295Wh With PCM and wires 50mm LiPo battery Type 3.7V Rechargeable Hot Selling Lithium Polymer Batteries LP652526 350mAh Voltage 3.7V Energy 1.295Wh Net Weight 7 g Detail Protection...
Standard lithium polymer batteries LP102731 850mAh
Rechargeable lithium polymer batteries LP102731 850mAh With PCM & wires 50mm & connecor LiPo battery Type Small lithium polymer batteries 850mAh LP102731 Voltage 3.7V Energy 3.145Wh Net Weight 15g Detail Protection circuit&50mm wires LiPo Battery Size...
Rechargeable lithium polymer batteries LPR653929 665mAh
Rechargeable lithium polymer batteries LPR653929 665mAh With PCM and wires 50mm LiPo battery Type Small lithium polymer batteries 665mAh LPR653929 Voltage 3.7V Energy 2.46Wh Net Weight 7 g Detail Protection circuit&50mm wires LiPo Battery Size 6.5mm*39mm*30mm...
Rechargeable lithium polymer batteries LP502540 500mAh
Rechargeable lithium polymer batteries LP502540 500mAh With PCM and wires 50mm LiPo battery Type Small lithium polymer batteries 500mAh LP502540 Voltage 3.7V Energy 1.85Wh Net Weight 7 g Detail Protection circuit&50mm wires LiPo Battery Size 5.0mm*25mm*41mm...
Rechargeable lithium polymer batteries LP403040 430mAh
Rechargeable lithium polymer batteries LP403040 430mAh With PCM and wires 50mm LiPo battery Type Small lithium polymer batteries 430mAh LP403040 Voltage 3.7V Energy 1.591Wh Net Weight 7 g Detail Protection circuit&50mm wires LiPo Battery Size 4.0mm*30mm*41mm...
Rechargeable lithium polymer batteries LP702020 230mAh
Rechargeable lithium polymer batteries LP702020 230mAh With PCM and 10K NTC & wires 50mm LiPo battery Type Small lithium polymer batteries 230mAh LP702020 Voltage 3.7V Energy 0.851Wh Net Weight 2 g Detail Protection circuit&50mm wires LiPo Battery Size...
Rechargeable lithium polymer batteries LP502025 200mAh
Rechargeable lithium polymer batteries LP502025 200mAh With PCM and wires 50mm LiPo battery Type Small lithium polymer batteries 200mAh LP502025 Voltage 3.7V Energy 0.74Wh Net Weight 2 g Detail Protection circuit&50mm wires LiPo Battery Size 5.0mm*20mm*26mm...